Welding Preheat Temperature Calculator — EN 1011-2 CEN Method B

By /



Use this free online welding preheat temperature calculator to determine the minimum preheat temperature for structural carbon and low-alloy steel welding. The calculator implements CEN Method B (EN 1011-2 Annex C) — the most widely used European standard — as well as the CE(IIW) method for a quick cross-check. Simply enter the steel composition, plate thickness, and filler metal hydrogen content.

Welding Preheat Temperature Calculator


CE(IIW)—
Pcm—
CEN (Annex C) Carbon Equivalent Cp—
Minimum Preheat Temperature T_p0 (CEN Method B)—
Preheat Recommendation—

Formula: CE(IIW) = C + Mn/6 + (Cr+Mo+V)/5 + (Ni+Cu)/15
Pcm = C + Si/30 + (Mn+Cu+Cr)/20 + Ni/60 + Mo/15 + V/10 + 5B
EN 1011-2 Annex C Cp = C + Mn/6 + (Cr+Mo+V)/5 + (Ni+Cu)/15
T_p0 (°C) = 697×Cp − 0.175×t^0.5 + 0.571×t×Cp − 26×HD^0.5 + 296
Standard: EN 1011-2:2001 Annex C (CEN Method B)

Annealing Process Types — Temperature Ranges Relative to A1 and A3 0°C 400 700 727 A1 800 912 A3 950+ A1 A3 Stress Relief550–650°C Spheroidise690–720°C Full Anneal30–50°C above A3 Normaliseabove A3, air cool No phase change Spheroidite forms Coarse pearlite Fine pearlite © metallurgyzone.com/
Figure: Steel annealing process types and their temperature ranges relative to A1 (727°C) and A3 (912°C) critical temperatures. © metallurgyzone.com/

How to Use the Preheat Calculator

Enter the full chemical composition of your steel (from the mill test certificate). If an element is not present or not specified, enter 0. Select the appropriate hydrogen content class for your welding consumable — check the filler metal data sheet for the declared diffusible hydrogen value. Enter the actual plate thickness at the joint and your planned heat input.

Understanding the Results

CE(IIW) — the International Institute of Welding carbon equivalent, widely used in structural codes (EN 1011-1, AWS D1.1). Values above 0.45 indicate increasing cold-cracking risk. Values above 0.60 require careful procedure control with mandatory preheat.

Pcm — the Ito-Bessyo cracking parameter, developed for low-carbon HSLA steels (<0.15% C). More sensitive to elements like B, Si, and Ni than CE(IIW). Commonly used for high-strength plates (S460–S960).

T_p0 (minimum preheat) — the lowest initial temperature at which the hydrogen-induced cold cracking risk is eliminated under the specified conditions. Always round up to the nearest 25°C increment in practice. Maintain preheat throughout the welding sequence including interpass temperature.

Preheat Methods and Verification

  • Gas flame heating: For preheat up to 150°C. Use an infra-red thermometer or temperature-indicating sticks (Tempilstik) to verify. Minimum measurement distance: 75mm from the weld preparation.
  • Electric resistance blankets / induction: For preheat 100–300°C. More uniform heat distribution; mandatory for P91 and other creep steels.
  • Oven preheating: For small components; provides the most uniform preheat but impractical for large fabrications.
  • Post-heat: After welding, maintain at preheat temperature for 1–2 hours before allowing to cool. Essential for high-CE steels (>0.55) and thick sections (>50mm).

References

  • EN 1011-2:2001 Welding — Recommendations for welding of metallic materials — Part 2: Arc welding of ferritic steels. Annex C (CEN Method B).
  • AWS D1.1/D1.1M:2020 Structural Welding Code — Steel. Annex I.
  • BS EN ISO 3690:2018 Welding and allied processes — Determination of hydrogen content in arc weld metal.

Leave a Comment

Your email address will not be published. Required fields are marked *

Scroll to Top